Cisco ASR 903 Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. ASR 903
  6. Manual

Cisco ASR 903 Manual

Hide thumbs Also See for ASR 903:
Table of Contents

Advertisement

Quick Links

See also: Troubleshooting Manual , Instruction and Installation Manual
Cisco ASR 903 Router Design and Deployment
Guide
Version 1.0
Last Updated: September 11, 2013
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-30526-01

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR 903

Summary of Contents for Cisco ASR 903

  • Page 1 Cisco ASR 903 Router Design and Deployment Guide Version 1.0 Last Updated: September 11, 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-30526-01...
  • Page 2 ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.

  • Page 3: Table Of Contents

    CONTENTS Introduction ............................... 6 Chapter 1 Cisco ASR 903 Chassis ..............7 Chapter 2 Layer 2 Solution ................8 Ethernet Flow Point (EFP) ........................8 Bridge Domain Interface with EFP, Sub-interface ................... 9 Ethernet Virtual Circuit using Regular EFPs .................... 9 Verifying Connectivity ........................
  • Page 4 New l2vpn Commands ........................... 57 Port mode by using Encapsulation Default .................... 58 Verify the L2VPN is up and running and CE1 can reach CE2, vice versa........59 Multi-segment Pseudowire ........................59 Verifying Pseudowire ......................... 60 Ethernet OAM ............................61 Connectivity Fault Management ......................
  • Page 5 Verifying Clocking ..........................135 PTP Configuration ..........................138 Verifying PTP and Clock Synchronization ..................140 Chapter 12 Cisco ASR 903 Software Upgrade ......... 143 Software Boot up options ........................143 Consolidated package mode ......................143 Sub package mode .......................... 144 ISSU One Shot Upgrade Overview ......................

  • Page 6: Introduction

    Introduction This document provides design guidance, and detailed configurations for deployment of the Cisco ASR 903 in service provider carrier Ethernet and mobile backhaul network. The design guide examples are created to help people who work on Cisco ASR 903 configuration.

  • Page 7: Chapter 1 Cisco Asr 903 Chassis

    Chapter 1 Cisco ASR 903 Chassis The Cisco ASR 903 Router has the following hardware features: • 3-RU modular chassis designed for installation in a 300 mm European Telecommunications Standards Institute (ETSI) cabinet • Up to six interface modules •...

  • Page 8: Chapter 2 Layer 2 Solution

    (second-)dot1q range Exact Outermost vlan, cos match. encapsulation dot1q vlan cos cos Ranged combinations of outermost vlan and second tag encapsulation dot1q range cos cos (second-)dot1q range cos cos ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 9: Bridge Domain Interface With Efp, Sub-Interface

    Bridge Domain Interface with EFP, Sub-interface The Cisco ASR 903 router does not support sub-interfaces as on the other Cisco platforms but a workaround can be used by pairing an Ethernet flow point (EFP) with a bridge domain interface (BDI).
  • Page 10 GigabitEthernet0/1/0 service-instance 11 ! vlan tag 11 for CE1 subnet B member GigabitEthernet0/1/2 service-instance 11 interface GigabitEthernet0/1/0 description interface to CE1 no ip address negotiation auto service instance 10 ethernet ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 11 10 ethernet encapsulation dot1q 10 rewrite ingress tag pop 1 symmetric service instance 11 ethernet encapsulation dot1q 20 second-dot1q 11 ! vlan tag 20 & 11 rewrite ingress tag pop 2 symmetric Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 12: Verifying Connectivity

    Nile Mac Address Entries mac addr type ports ---------------------------------------------------------------------------------- c8f9.f98d.103f DYNAMIC Gi0/1/2.Efp10 c8f9.f98d.503f DYNAMIC Gi0/1/0.Efp10 Router# show bridge-domain 11 Bridge-domain 11 (2 ports in all) State: UP Mac learning: Enabled Aging-Timer: 300 second(s) ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 13: Ethernet Virtual Circuit Using Trunk Efp

    1 symmetric ! to use BDI, pop is required. ! otherwise rewrite may not be needed. service instance 11 ethernet encapsulation dot1q 11 rewrite ingress tag pop 1 symmetric Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 14 ! in this case, we only need vlan 30 and 40 rewrite ingress tag pop 1 symmetric bridge-domain from-encapsulation ! outer vlan tag is used as bridge-domain ASR903-CE2 Configuration interface GigabitEthernet0/1/2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 15: Verifying The Configuration

    Mac learning: Enabled Aging-Timer: 300 second(s) Maximum address limit: 256000 GigabitEthernet0/1/0 service instance 10 GigabitEthernet0/1/2 service instance 1 Nile Mac Address Entries mac addr type ports ---------------------------------------------------------------------------------- c8f9.f98d.103f DYNAMIC Gi0/1/2.tefp1 c8f9.f98d.503f DYNAMIC Gi0/1/0.Efp10 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 16: Layer 2 Protocol Peering

    L2 protocol peering is needed for devices to use MSTP with neighbor device. Now another trunk link is added between two PE routers, and spanning-tree should be enabled to prevent loop. ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 17: Verify Spanning-Tree Configuration

    2 ethernet encapsulation untagged l2protocol peer ! enable l2protocol peering bridge-domain 1 Verify Spanning-tree Configuration ASR903-PE1# show span vlan 30 MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 7010.5c51.8fbb Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 18: Ethernet Port-Channel

    Gi0/1/2 Altn BLK 20000 128.17 Ethernet Port-channel Cisco ASR 903 router supports layer 2 and layer 3 port-channels, and only LACP is supported for link aggregation. Here are the steps to create layer 3 port-channel. interface Port-channel channel number ip address x.x.x.x y.y.y.y...
  • Page 19 Layer 2 Solution Ethernet Port-channel ▀ Three modes are supported on the Cisco ASR 903 router. • LACP—channel-group 1 mode { active | passive} • On—channel-group 1 On mode will force member link into port-channel whether other end joins or not. On mode is not recommended as traffic can be black holed if the peering end does not join port-channel.
  • Page 20 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out Router# show bridge-domain 40 Bridge-domain 40 (2 ports in all) State: UP Mac learning: Enabled Aging-Timer: 300 second(s) ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 21: G.8032

    (port 1) (port 0) For G.8032, CFM can be configured under either an EFP or main Ethernet interface for failure detection. Following is a configuration example for CFM under EFP scenario. Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 22 1000-2999 rewrite ingress tag pop 1 symmetric bridge-domain from-encapsulation ethernet ring g8032 profile g8032_profile timer wtr 1 ethernet ring g8032 g8032_ring port0 interface GigabitEthernet0/2/1 port1 interface GigabitEthernet0/2/0 instance 1 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 23 1 ethernet evc_name encapsulation dot1q 10 bridge-domain 10 cfm mep domain g8032_domain mpid 2 continuity-check static rmep rmep mpid 1 service instance trunk 1000 ethernet encapsulation dot1q 1000-2999 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 24 GigabitEthernet0/2/1 no ip address negotiation auto service instance 1 ethernet evc_name encapsulation dot1q 10 bridge-domain 10 cfm mep domain g8032_domain mpid 1 continuity-check static rmep rmep mpid 2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 25 1 continuity-check static rmep rmep mpid 2 service instance trunk 1000 ethernet encapsulation dot1q 1000-2999 rewrite ingress tag pop 1 symmetric bridge-domain from-encapsulation interface GigabitEthernet0/2/1 no ip address negotiation auto Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 26 1 service instance 1 ethernet encapsulation dot1q 10 bridge-domain 10 service instance trunk 1000 ethernet encapsulation dot1q 1000-2999 rewrite ingress tag pop 1 symmetric bridge-domain from-encapsulation interface GigabitEthernet0/2/1 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 27 3.3ms interface GigabitEthernet0/2/0 no ip address negotiation auto ethernet cfm mep domain g8032_domain mpid 1 service g8032_service continuity-check static rmep rmep mpid 2 service instance 1 ethernet encapsulation dot1q 10 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 28 3.3ms interface GigabitEthernet0/2/0 no ip address negotiation auto ethernet cfm mep domain g8032_domain mpid 2 service g8032_service continuity-check static rmep rmep mpid 1 service instance 1 ethernet encapsulation dot1q 10 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 29 1 service g8032_service port continuity-check continuity-check interval 3.3ms interface GigabitEthernet0/2/0 no ip address negotiation auto ethernet cfm mep domain g8032_domain mpid 1 service g8032_service Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 30: Verifying G.8032

    1 Verifying G.8032 ASR903-R1# show ethernet ring g8032 brief R: Interface is the RPL-link F: Interface is faulty B: Interface is blocked FS: Local forced switch MS: Local manual switch ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 31 WTR interval: 1 minutes Guard interval: 500 milliseconds HoldOffTimer: 0 seconds Revertive mode ASR903-R1# show ethernet ring g8032 status Ethernet ring g8032_ring instance 1 is RPL Owner node in Idle State Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 32 Ethernet ring g8032_ring instance 1 is Normal Node node in Idle State Port0: GigabitEthernet0/2/0 (Monitor: GigabitEthernet0/2/0) APS-Channel: GigabitEthernet0/2/0 Status: Non-RPL Remote R-APS NodeId: d0c2.8216.29bf, BPR: 0 Port1: GigabitEthernet0/2/1 (Monitor: GigabitEthernet0/2/1) APS-Channel: GigabitEthernet0/2/1 Status: Non-RPL Remote R-APS NodeId: 0000.0000.0000, BPR: 0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 33 Port1: GigabitEthernet0/2/0 (Monitor: GigabitEthernet0/2/0) APS-Channel: GigabitEthernet0/2/0 Status: Non-RPL Remote R-APS NodeId: 0000.0000.0000, BPR: 0 APS Level: 7 Profile: g8032_profile WTR interval: 1 minutes Guard interval: 500 milliseconds HoldOffTimer: 0 seconds Revertive mode Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 34 Port1: GigabitEthernet0/2/1 (Monitor: GigabitEthernet0/2/1) APS-Channel: GigabitEthernet0/2/1 Status: RPL, blocked Remote R-APS NodeId: d0c2.8216.29bf, BPR: 0 APS Level: 7 Profile: g8032_profile WTR interval: 1 minutes Guard interval: 500 milliseconds HoldOffTimer: 0 seconds Revertive mode ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 35: Protection Switching

    REQ/ACK: 2/2 Instance 1 is in Unblocked state ASR903-R1# show ethernet ring g8032 status Ethernet ring g8032_ring instance 1 is RPL Owner node in Protection State Port0: GigabitEthernet0/2/1 (Monitor: GigabitEthernet0/2/1) APS-Channel: GigabitEthernet0/2/1 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 36 Instance 1 is in Blocked state ASR903-R2# show ethernet ring g8032 status Ethernet ring g8032_ring instance 1 is Normal Node node in Protection State Port0: GigabitEthernet0/2/0 (Monitor: GigabitEthernet0/2/0) APS-Channel: GigabitEthernet0/2/0 Status: Non-RPL ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 37 Port0: GigabitEthernet0/2/1 (Monitor: GigabitEthernet0/2/1) APS-Channel: GigabitEthernet0/2/1 Status: Non-RPL, faulty, blocked Remote R-APS NodeId: 0000.0000.0000, BPR: 0 Port1: GigabitEthernet0/2/0 (Monitor: GigabitEthernet0/2/0) APS-Channel: GigabitEthernet0/2/0 Status: Non-RPL Remote R-APS NodeId: d0c2.8216.20bf, BPR: 1 APS Level: 7 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 38 Port1: GigabitEthernet0/2/1 (Monitor: GigabitEthernet0/2/1) APS-Channel: GigabitEthernet0/2/1 Status: RPL Remote R-APS NodeId: d0c2.8216.20bf, BPR: 1 APS Level: 7 Profile: g8032_profile WTR interval: 1 minutes Guard interval: 500 milliseconds HoldOffTimer: 0 seconds Revertive mode ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 39: Rep

    Layer 2 Solution REP ▀ The Resilient Ethernet Protocol (REP) is a Cisco proprietary protocol that provides an alternative to the Spanning Tree Protocol (STP). REP provides a way to control network loops, handle link failures, and improve convergence time. It controls a group of ports connected in a segment, ensures that the segment does not create any bridging loops, and responds to link failures within the segment.
  • Page 40 1 symmetric bridge-domain from-encapsulation interface GigabitEthernet0/2/0 no ip address negotiation auto rep segment 1 service instance trunk 1 ethernet encapsulation dot1q 1-4094 rewrite ingress tag pop 1 symmetric bridge-domain from-encapsulation ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 41: Verifying Rep

    REP Segment 1 BridgeName PortName Edge Role ---------------- ---------- ---- ---- ASR903-R1 Gi0/2/0 ASR903-R2 Gi0/2/0 Open ASR903-R2 Gi0/2/1 Open ASR903-R3 Gi0/2/1 Open ASR903-R3 Gi0/2/0 Open ASR903-R4 Gi0/2/0 Open Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 42: Link Failover

    REP Segment 1 Warning: REP detects a segment failure, topology may be incomplete BridgeName PortName Edge Role ---------------- ---------- ---- ---- ASR903-R1 Gi0/2/0 Open ASR903-R2 Gi0/2/0 Open ASR903-R2 Gi0/2/1 Fail ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 43 *Jun 10 17:14:13.396: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2/1, changed state to up ASR903-R1# show rep topology REP Segment 1 BridgeName PortName Edge Role ---------------- ---------- ---- ---- ASR903-R1 Gi0/2/0 ASR903-R2 Gi0/2/0 Open ASR903-R2 Gi0/2/1 Open Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 44 ASR903-R4# show rep topology REP Segment 1 BridgeName PortName Edge Role ---------------- ---------- ---- ---- ASR903-R1 Gi0/2/0 ASR903-R2 Gi0/2/0 Open ASR903-R2 Gi0/2/1 Open ASR903-R3 Gi0/2/1 Open ASR903-R3 Gi0/2/0 Open ASR903-R4 Gi0/2/0 Open ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 45: Chapter 3 Basic Mpls Vpn Configuration

    Configuration of OSPF and BFD OSPF is chosen as IGP protocol and BFD is used to detect link failure for fast convergence. ASR 903 supports both software and hardware based BFD sessions. When a BFD session is created, depending on the hardware resources and nature of BFD session, it can be offloaded to hardware.

  • Page 46: Verifying The Configuration

    Registered protocols: OSPF CEF Uptime: 00:28:22 Last packet: Version: 1 - Diagnostic: 0 State bit: Up - Demand bit: 0 Poll bit: 0 - Final bit: 0 C bit: 1 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 47: Configuration Of Bgp And Vrf On Pe Routers

    Min Echo interval: 0 In Cisco IOS XE Release 3.9S, echo function is supported. BFD timer on the Cisco ASR 903 router can be as low as 3.3ms and timer lower than 50ms can be set by using BFD template.

  • Page 48: Ce Related Configuration On Pe Routers

    41 vrf CustomerA ! use OSPF between PE and CE router-id 192.168.13.3 redistribute bgp 100 subnets ! redistribute VPNv4 routes from other network 192.168.13.3 0.0.0.0 area 41 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 49 192.168.40.1 255.255.255.248 interface BDI42 ! virtual BDI interface for CustomerB ip vrf forwarding CustomerB ip address 192.168.41.1 255.255.255.248 router ospf 42 vrf CustomerB redistribute bgp 100 subnets network 192.168.41.0 0.0.0.255 area 42 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 50: Configuration Of Ce Routers

    ! routes to advertise out from CE1-A ip address 172.16.0.1 255.255.255.0 ip ospf network point-to-point interface Loopback111 ! routes to advertise out from CE1-A ip address 172.16.1.1 255.255.255.0 ip ospf network point-to-point ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 51 Loopback90 ip address 172.16.10.1 255.255.255.0 interface Loopback91 ip address 172.16.11.1 255.255.255.0 interface Loopback100 ip address 10.5.10.1 255.255.255.0 ip ospf network point-to-point interface Loopback101 ip address 10.5.11.1 255.255.255.0 ip ospf network point-to-point Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 52: Verification Of Pe And Ce Routers

    ! routes from PE1 *>i 172.16.1.0/24 10.10.3.3 ! routes from PE1 *> 172.16.10.0/24 192.168.40.2 0 64101 I ! routes from local *> 172.16.11.0/24 192.168.40.2 0 64101 I ! CE *>i 192.168.13.0/29 10.10.3.3 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 53: Verifying The Routing Tables On Ce Devices

    172.16.0.0/16 is variably subnetted, 6 subnets, 2 masks 172.16.0.0/24 [20/0] via 192.168.40.1, 1d00h ! routes from CustomerA site 1 172.16.1.0/24 [20/0] via 192.168.40.1, 1d00h ! routes from CustomerA site 1 172.16.10.0/24 is directly connected, Loopback90 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 54 Sending 5, 100-byte ICMP Echos to 10.5.0.1, timeout is 2 seconds: Packet sent with a source address of 10.5.10.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 55: Chapter 4 Ethernet Over Mpls

    GigabitEthernet0/1/0 no ip address negotiation auto no keepalive service instance 2 ethernet encapsulation dot1q 200 xconnect 10.10.3.3 200 encapsulation mpls ! create PW, VCID must be same CE1 Configuration interface BDI200 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 56 GigabitEthernet0/1/0 service instance 2 ethernet encapsulation dot1q 300 ! notice different vlan tag rewrite ingress tag pop 1 symmetric ! pop the vlan header xconnect 10.10.4.4 200 encapsulation mpls ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 57: New L2Vpn Commands

    There are a new set of commands available to create EoMPLS as illustrated in PE configuration. ASR903-PE1 Configuration interface GigabitEthernet0/1/0 no ip address negotiation auto no keepalive service instance 1 ethernet Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 58: Port Mode By Using Encapsulation Default

    ! this encapsulation catches all xconnect 10.10.4.4 100 encapsulation mpls ASR903-PE2 Configuration interface GigabitEthernet0/1/0 no ip address negotiation auto no keepalive service instance 1 ethernet encapsulation default xconnect 10.10.3.3 100 encapsulation mpls ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 59: Verify The L2Vpn Is Up And Running And Ce1 Can Reach Ce2, Vice Versa

    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms Multi-segment Pseudowire Multi-segment pseudowire extends the pseudo wire into multiple autonomous systems. In the case below, PW between PE1 and PE2 have two segments. Figure 9. Multi-segment Pseudowire Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 60: Verifying Pseudowire

    Verifying Pseudowire ASR903-P1# show mpls l2transport vc Local intf Local circuit Dest address VC ID Status ------------- ------------------------- ----------------- -------- ---------- pw100010 10.10.4.4 1100 10.10.3.3 1100 pw100009 10.10.3.3 1100 10.10.4.4 1100 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 61: Ethernet Oam

    ! enable CFM on the router ethernet cfm domain PE1-2 level 6 service EVC-PE-200 evc evc-200 continuity-check continuity-check interval 1s ethernet cfm logging ethernet evc evc-200 interface GigabitEthernet0/1/0 no ip address negotiation auto no keepalive Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 62: Verify Oam

    Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/4 ms ASR903-PE2# traceroute ethernet mpid 1200 domain PE1-2 service EVC-PE-200 source 1201 Type escape sequence to abort. TTL 64. Linktrace Timeout is 5 seconds ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 63 ASR903-PE1# show ip sla statistics 110 (detail) IPSLAs Latest Operation Statistics IPSLA operation id: 110 Delay Statistics for Y1731 Operation 110 Type of operation: Y1731 Delay Measurement Latest operation start time: *02:24:08.354 UTC Sat Aug 10 2013 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 64 Latest operation return code: OK Distribution Statistics: Interval Start time: *02:24:08.354 UTC Sat Aug 10 2013 Elapsed time: 29 seconds Number of measurements initiated: 24 Number of measurements completed: 24 Flag: OK ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 65: Chapter 5 Virtual Private Lan Service - Vpls

    (see the figure below). Figure 10. VPLS Manually Provisioned VPLS PE-1 Configuration ! use the legacy l2 VPLS configuration commands l2 vfi VPLS30 manual vpn id 30 bridge-domain 30 neighbor 10.10.3.3 encapsulation mpls Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 66: Verifying Vc Neighbors

    Legend: RT=Route-target, S=Split-horizon, Y=Yes, N=No VFI name: VPLS30, state: up, type: multipoint, signaling: LDP VPN ID: 30 Bridge-Domain 30 attachment circuits: Neighbors connected via pseudowires: Peer Address VC ID 10.10.2.2 10.10.3.3 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 67: Vpls - Bgp Auto-Discovery And Ldp Signaling

    35 ! associate Attachement circuit with VPLS VFI member GigabitEthernet0/1/0 service-instance 35 member vfi VPLS35 interface GigabitEthernet0/1/0 no ip address negotiation auto no keepalive service instance 35 ethernet encapsulation dot1q 35 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 68: Verifying Vpls Neighbors

    PE-1# show vfi name VPLS35 Legend: RT=Route-target, S=Split-horizon, Y=Yes, N=No VFI name: VPLS35, state: up, type: multipoint, signaling: LDP VPN ID: 35, VPLS-ID: 100:35 RD: 100:35, RT: 100:35 Bridge-Domain 35 attachment circuits: ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 69: Vpls - Bgp Auto-Discovery And Signaling

    10.10.3.3 update-source Loopback10 address-family l2vpn vpls neighbor 10.10.2.2 activate neighbor 10.10.2.2 send-community extended neighbor 10.10.2.2 suppress-signaling-protocol ldp ! suppress LDP to use neighbor 10.10.3.3 activate neighbor 10.10.3.3 send-community extended neighbor 10.10.3.3 suppress-signaling-protocol ldp Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 70: Verifying Vpls

    10.10.2.2 activate neighbor 10.10.2.2 send-community extended neighbor 10.10.2.2 suppress-signaling-protocol ldp Verifying VPLS PE-1# show vfi name VPLS30 Legend: RT=Route-target, S=Split-horizon, Y=Yes, N=No VFI name: VPLS30, state: up, type: multipoint, signaling: BGP ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 71: Vpls Hub-Spoke Configuration

    In this case, it can be disabled. Figure 11. VPLS Hub-Spoke PE-1 Configuration l2 vfi VPLS30 manual vpn id 30 bridge-domain 30 neighbor 10.10.3.3 encapsulation mpls no-split-horizon neighbor 10.10.2.2 encapsulation mpls no-split-horizon ! Interface to CE-1 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 72: H-Vpls With Ethernet Q-In-Q Access

    1 ethernet encapsulation dot1q 10 bridge-domain 10 Interface to N-PE S-TAG 30 is added on top of C-tag 10 interface GigabitEthernet0/0/1 service instance 3 ethernet encapsulation dot1q 30 second-dot1q 10 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 73: H-Vpls With Mpls Access

    10.10.2.2 encapsulation mpls H-VPLS with MPLS Access Figure 13. H-VPLS with MPLS Access For H-VPLS with MPLS access based on pseudowire redundancy, the MPLS network has pseudowires to the VPLS core N-PE routers. Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 74 GigabitEthernet0/0/7 service-instance 2 ! this is local attachement circuit member vfi VPLS30 ! To MPLS access u-PE member 10.10.10.10 1300 encapsulation mpls interface GigabitEthernet0/0/7 service instance 2 ethernet encapsulation dot1q 30 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 75: Chapter 6 Tdm

    Optical Channel Mapping and Related Configuration ▀ Chapter 6 TDM The Cisco ASR 903 router supports 16 T1/E1 and 4 port OC-3/1 port OC-12 combo card. HDLC, PPP, MLPPP, ATM and CEM are supported on the Cisco ASR 903 router.
  • Page 76 ▀ Optical Channel Mapping and Related Configuration Figure 15. OC-3 T1 Mapping at DS1 Level in SDH Figure 16. OC-3 T1 Mapping at DS1 Level in SONET ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 77 Optical Channel Mapping and Related Configuration ▀ Figure 17. OC-12 E1 Mapping at DS1 Level in SDH Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 78 ▀ Optical Channel Mapping and Related Configuration Figure 18. OC-12 T1 Mapping at DS1 Level in SDH ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 79 Circuit Emulation Service over Packet-Switched Network (CESoPSN) ▀ Figure 19. OC-12 T1 Mapping at DS1 Level in SONET Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 80: Circuit Emulation Service Over Packet-Switched Network (Cesopsn)

    CE1 Configuration (ASR903) controller SONET 0/5/0 framing sdh clock source line aug mapping au-4 au-4 1 tug-3 1 mode c-12 tug-2 1 e1 1 channel-group 0 timeslots 1-31 ! the CEM circuit ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 81: Verifying Cem

    Success rate is 100 percent (5/5), round-trip min/avg/max = 7/9/15 ms Structure-Agnostic TDM over Packet (SAToP) Figure 21. SAToP ASR903-R3 ASR903-R4 ASR903-R1 ASR903-R2 SONET 0/4/0 E 1 0/5/0 Gi 0/2/1 Gi 0/2/1 10.10.3.x (172.16.1.1) (172.16.2.2) (172.16.3.3) (172.16.4.4) Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 82 1 e1 1 framing unframed au-4 1 tug-3 2 mode c-12 au-4 1 tug-3 3 mode c-12 interface Loopback0 ip address 172.16.3.3 255.255.255.255 interface GigabitEthernet0/2/1 ip address 10.10.3.2 255.255.255.0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 83: Verifying Tdm Pw

    Preferred path: not configured Default path: active Next hop: 10.10.3.2 Create time: 01:10:31, last status change time: 00:51:21 Last label FSM state change time: 00:57:43 Signaling protocol: LDP, peer 172.16.3.3:0 up Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 84 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs 0 Near-end path failures, 0 Far-end path failures, 0 SEF/AIS Secs ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 85 SSM segment/switch IDs: 8194/4096 (used), PWID: 1 VC statistics: transit packet totals: receive 3725129, send 3412605 transit byte totals: receive 1014481148, send 900927720 transit packet drops: receive 0, seq error 0, send 0 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 86 LOP = 0 PSE = 0 NSE = 0 NEWPTR = 0 LOM = 0 PLM = 1 UNEQ = 0 Active Defects: None Detected Alarms: None Asserted/Active Alarms: None ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 87 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs 0 Unavail Secs, 0 Stuffed Secs Total Data (last 4 15 minute intervals): Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 88: Pos Configuration

    POS0/5/0.1 is up, line protocol is up Hardware is SPA_4xOC3_1xOC12 Internet address is 10.10.100.3/29 MTU 4470 bytes, BW 155000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP Open ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 89: Oc-3 Sonet Pos

    1 - 3 pos ! create POS interface interface POS0/5/0.1 ip address 10.10.100.1 255.255.255.248 encapsulation ppp ! using encapsulation PPP, default is HDLC ASR903-R3 Configuration controller SONET 0/5/0 framing sonet clock source internal Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 90: Oc-12 Sdh Pos

    Optical combo card can also be configured as 1 OC-12 port by using the following command. card type oc12 0 5 ASR903-R1 Configuration controller SONET 0/5/0 framing sonet clock source line sts-1 1 - 12 pos ! create POS interface ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 91 ! using encapsulation PPP, default is HDLC ASR903-R3 Configuration controller SONET 0/5/0 framing sonet clock source internal sts-1 1 - 12 pos interface POS0/5/0.1 ip address 10.10.100.3 255.255.255.248 encapsulation ppp Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 92: Chapter 7 Mpls Te Configuration

    Figure 22. MPLS-TE ASR903-R3 Loopback10: 10.10.3.3 ASR903-R1 Loopback10: 10.10.1.1 Gi0/1/0 Gi0/1/1 ASR903-R4 x.x.13.3 x.x.34.3 Loopback10: 10.10.4.4 Gi0/1/1 Gi0/1/1 x.x.13.1 x.x.34.4 Gi0/1/0 Gi0/1/0 x.x.12.1 x.x.24.4 Gi0/1/0 Gi0/1/2 x.x.12.2 x.x.24.2 ASR903-R2 Loopback10: 10.10.2.2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 93: Basic Steps To Configure Traffic Engineering

    30M under gi0/1/0 for traffic engineering. interface GigabitEthernet0/1/1 ip rsvp bandwidth 40000 ! Reserved bandwidth in kbps interface GigabitEthernet0/1/0 ip rsvp bandwidth 30000 ! Reserved 30M under another interface Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 94 GigabitEthernet0/1/2 ip address 10.10.24.2 255.255.255.248 ip ospf dead-interval 3 ip ospf hello-interval 1 negotiation auto mpls ip mpls traffic-eng tunnels ip rsvp bandwidth 30000 interface GigabitEthernet0/1/0 ip address 10.10.12.2 255.255.255.248 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 95: Dynamic Te Tunnel

    Figure 23. Dynamic TE Tunnel ASR903-R3 Loopback10: 10.10.3.3 ASR903-R1 ASR903-R4 Loopback10: 10.10.1.1 Gi0/1/0 Gi0/1/1 Loopback10: 10.10.4.4 x.x.13.3 x.x.34.3 Gi0/1/1 Gi0/1/1 x.x.13.1 x.x.34.4 Gi0/1/0 Gi0/1/0 x.x.12.1 x.x.24.4 Gi0/1/0 Gi0/1/2 x.x.12.2 x.x.24.2 ASR903-R2 Loopback10: 10.10.2.2 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 96 Last update from 10.10.13.3 on GigabitEthernet0/1/1, 00:00:11 ago Routing Descriptor Blocks: 10.10.13.3, from 10.10.4.4, 00:00:11 ago, via GigabitEthernet0/1/1 Route metric is 3, traffic share count is 1 * 10.10.12.2, from 10.10.4.4, 00:00:11 ago, via GigabitEthernet0/1/0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 97: Explicit Path Configuration

    3, type explicit R1-R2-R4-1 (Basis for Setup, path weight 2) Config Parameters: Bandwidth: 1000 kbps (Global) Priority: 5 Affinity: 0x0/0xFFFF Metric Type: TE (default) AutoRoute: enabled LockDown: disabled Loadshare: 1000 [2000000] bw-based auto-bw: disabled Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 98: Explicit Path By Using Affinity

    LSP the tunnel uses. Figure 24. Explicit Path ASR903-R3 Loopback10: 10.10.3.3 ASR903-R1 ASR903-R4 Loopback10: 10.10.1.1 Gi0/1/0 Gi0/1/1 Loopback10: 10.10.4.4 Tun12 Gi0/1/1 Gi0/1/1 Gi0/1/0 Gi0/1/0 Tun13 Gi0/1/0 Gi0/1/2 ASR903-R2 Loopback10: 10.10.2.2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 99: Verify Te Tunnel And Tunnel Path

    Metric Type: TE (default) AutoRoute: enabled LockDown: disabled Loadshare: 500 [4000000] bw-based auto-bw: disabled Active Path Option Parameters: State: dynamic path option 3 is active BandwidthOverride: disabled LockDown: disabled Verbatim: disabled Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 100 0x2 mask 0x2 tunnel mpls traffic-eng path-option 3 dynamic interface GigabitEthernet0/1/0 mpls traffic-eng attribute-flags 0x2 ASR903-R2 Configuration interface GigabitEthernet0/1/0 mpls traffic-eng attribute-flags 0x2 interface GigabitEthernet0/1/2 mpls traffic-eng attribute-flags 0x2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 101: Traffic Engineering Fast Reroute

    10.10.4.4 tunnel mpls traffic-eng priority 3 3 tunnel mpls traffic-eng bandwidth 500 tunnel mpls traffic-eng affinity 0x2 mask 0x2 tunnel mpls traffic-eng path-option 3 dynamic Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 102: Verifying Fast Reroute Configuration

    Original: out i/f: Gi0/1/1, label: 26, nhop: 10.10.4.4 nnhop: 10.10.4.4, nnhop rtr id: 10.10.4.4 With FRR: out i/f: Tu13, label: implicit-null LSP bw: 500 kbps, Backup level: any-unlim, type: any pool Path Protection: None ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 103: Bfd Triggered Te Fast Reroute

    10.10.34.3 255.255.255.248 negotiation auto mpls ip mpls traffic-eng tunnels mpls traffic-eng attribute-flags 0x1 bfd interval 50 min_rx 50 multiplier 3 ip rsvp bandwidth 40000 ip rsvp signalling hello bfd Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 104: Verifying Bfd Triggered Fast Reroute

    - Final bit: 0 C bit: 1 Multiplier: 3 - Length: 24 My Discr.: 1 - Your Discr.: 1 Min tx interval: 1000000 - Min rx interval: 1000000 Min Echo interval: 50000 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 105: Chapter 8 Lfa & Remote Lfa (Rlfa)

    Figure 25. LFA (172.16.2.2) ASR903-R2 Gi 0/2/3 Gi 0/2/0 10.10.4.x 10.10.1.x Gi 0/2/0 Gi 0/2/0 Gi 0/2/2 Gi 0/2/1 ASR903-R1 ASR903-R4 (172.16.1.1) (172.16.4.4) 10.10.2.x 10.10.5.x Gi 0/2/2 Gi 0/2/3 ASR903-R3 (172.16.3.3) Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 106: Configuration For Lfa (With Ospf)

    Route metric is 3, traffic share count is 1 Repair Path: 10.10.1.2, via GigabitEthernet0/2/0 * 10.10.1.2, from 172.16.4.4, 00:00:06 ago, via GigabitEthernet0/2/0 Route metric is 3, traffic share count is 1 Repair Path: 10.10.2.2, via GigabitEthernet0/2/2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 107: Configuration For Rlfa (With Ospf)

    10.10.4.0 0.0.0.255 area 0 network 10.10.5.0 0.0.0.255 area 0 Configuration for rLFA (with ISIS) ASR903-R1 Configuration mpls label protocol ldp mpls ldp explicit-null mpls ldp session protection mpls ldp router-id Loopback0 force Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 108 GigabitEthernet0/2/3 ip address 10.10.4.1 255.255.255.0 ip router isis negotiation auto mpls ip isis network point-to-point router isis net 49.0001.0000.0000.0002.00 passive-interface Loopback0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 109 GigabitEthernet0/2/1 ip address 10.10.5.2 255.255.255.0 ip router isis negotiation auto mpls ip isis network point-to-point router isis net 49.0001.0000.0000.0004.00 passive-interface Loopback0 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 110: Verifying Rlfa

    172.16.3.3:0, label: 31 remote binding: lsr: 172.16.2.2:0, label: exp-null lib entry: 172.16.3.3/32, rev 262 local binding: label: 21 remote binding: lsr: 172.16.2.2:0, label: 17 remote binding: lsr: 172.16.4.4:0, label: 16 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 111 Last update from 10.10.1.2 on GigabitEthernet0/2/0, 00:30:30 ago Routing Descriptor Blocks: * 10.10.1.2, from 172.16.2.2, 00:30:30 ago, via GigabitEthernet0/2/0 Route metric is 2, traffic share count is 1 Repair Path: 172.16.4.4, via MPLS-Remote-Lfa2 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 112: Chapter 9 Bgp Pic & Rfc3107

    PIC for IP and MPLS-VPN feature creates and stores a backup/alternate path in the routing information base (RIB), forwarding information base (FIB), and Cisco Express Forwarding (CEF) so that when a failure is detected, the backup/alternate path can immediately take over, thus enabling fast failover.

  • Page 113: Configuration For Bgp Pic (With Ospf)

    172.16.3.3 remote-as 100 neighbor 172.16.3.3 update-source Loopback0 address-family ipv4 bgp additional-paths install network 172.16.1.1 mask 255.255.255.255 neighbor 172.16.2.2 activate neighbor 172.16.2.2 send-label neighbor 172.16.3.3 activate neighbor 172.16.3.3 send-label exit-address-family mpls ldp router-id Loopback0 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 114 172.16.22.22 update-source Loopback0 address-family ipv4 neighbor 172.16.1.1 activate neighbor 172.16.1.1 route-reflector-client neighbor 172.16.1.1 next-hop-self all neighbor 172.16.1.1 send-label neighbor 172.16.3.3 activate neighbor 172.16.22.22 activate neighbor 172.16.22.22 next-hop-self all neighbor 172.16.22.22 send-label exit-address-family ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 115 172.16.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 100 neighbor 172.16.2.2 update-source Loopback0 neighbor 172.16.11.11 remote-as 100 neighbor 172.16.11.11 update-source Loopback0 address-family ipv4 neighbor 172.16.1.1 activate neighbor 172.16.1.1 route-reflector-client neighbor 172.16.1.1 next-hop-self all Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 116 172.16.4.4 mask 255.255.255.255 network 10.10.7.0 mask 255.255.255.0 neighbor 172.16.11.11 activate neighbor 172.16.11.11 send-label neighbor 172.16.22.22 activate neighbor 172.16.22.22 send-label exit-address-family mpls ldp router-id Loopback0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 117 GigabitEthernet0/0/0/18 router bgp 100 ibgp policy out enforce-modifications address-family ipv4 unicast advertise best-external allocate-label all neighbor 172.16.3.3 remote-as 100 update-source Loopback10 address-family ipv4 unicast next-hop-self address-family ipv4 labeled-unicast next-hop-self neighbor 172.16.4.4 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 118 10.10.4.2 255.255.255.0 negotiation auto interface GigabitEthernet0/0/0/17 ipv4 address 10.10.7.1 255.255.255.0 negotiation auto interface GigabitEthernet0/0/0/18 ipv4 address 10.10.6.1 255.255.255.0 negotiation auto router ospf 10 router-id 172.16.22.22 area 0 interface GigabitEthernet0/0/0/16 area 20 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 119 172.16.4.4 remote-as 100 update-source Loopback10 address-family ipv4 unicast route-reflector-client next-hop-self address-family ipv4 labeled-unicast route-reflector-client next-hop-self neighbor 172.16.11.11 remote-as 100 update-source Loopback10 address-family ipv4 unicast route-policy DENY drop end-policy Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 120: Verifying Bgp Pic & Rfc3107

    0, tx pathid: 0x0 ASR903-R1# show ip bgp label Network Next Hop In label/Out label 172.16.1.1/32 0.0.0.0 imp-null/nolabel 172.16.4.4/32 172.16.3.3 nolabel/28 172.16.2.2 nolabel/28 10.10.7.0/24 172.16.3.3 nolabel/30 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 121 Known via "bgp 100", distance 200, metric 0, type internal Last update from 172.16.2.2 1d20h ago Routing Descriptor Blocks: * 172.16.2.2, from 172.16.2.2, 1d20h ago Route metric is 0, traffic share count is 1 AS Hops 0 MPLS label: 28 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 122 Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 123 Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2 seconds: Packet sent with a source address of 172.16.4.4 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/2 ms Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 124: Configuration For Bgp Pic & Rfc3107 (With Isis)

    GigabitEthernet0/2/0 ip address 10.10.1.2 255.255.255.0 ip router isis negotiation auto mpls ip isis circuit-type level-1 router isis net 49.0001.0000.0000.0002.00 passive-interface Loopback0 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 125 10.10.7.2 255.255.255.0 ip router isis negotiation auto mpls ip interface GigabitEthernet0/2/1 ip address 10.10.8.2 255.255.255.0 ip router isis negotiation auto mpls ip router isis net 49.0001.0000.0000.0004.00 is-type level-1 passive-interface Loopback0 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 126 1 net 49.0001.0000.0000.0022.00 interface Loopback10 passive address-family ipv4 unicast interface GigabitEthernet0/0/0/16 circuit-type level-2-only address-family ipv4 unicast interface GigabitEthernet0/0/0/17 circuit-type level-1 address-family ipv4 unicast interface GigabitEthernet0/0/0/18 circuit-type level-2-only address-family ipv4 unicast ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 127: Chapter 10 Qos

    Configuration for BGP PIC & RFC3107 (with ISIS) ▀ Chapter 10 Cisco ASR 903 supports three level hierarchical QoS, port, vlan and class level. Classification, marking, policing, shaping and LLQ are supported. At class level, you can have up to 8 classes including class-default under a policy- map.
  • Page 128 As a best practice, it is recommended to mark ingress packets into internal qos-group and then take action based on those qos-groups. Qos-groups are internal entities on the router and there are 100 usable qos-groups. ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 129 15 For more information on configuring QoS on the Cisco ASR 903 router, see the Quality of Service Configuration Guide for Cisco ASR 903 Router. Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 130: Chapter 11 Clocking

    10MHz inputs can be used as external clocking sources. 1PPS and ToD can be used for 1588 PTP. Figure 27. Cisco ASR903-RSP Table 3. Framing Modes for BITS Port on a Cisco ASR 903 Series Router BITS or SSU Port Support Matrix Framing Modes Supported SSM or QL Support Tx Port Rx Port...
  • Page 131 When the best available clock is to be selected, there are two modes for consideration. In quality disabled mode, only clock availability and priority matter, and quality level is ignored. In quality mode, quality level is used a selection criteria too. Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 132: Sync-E Configuration

    Elect Interface as Clocking Candidates network-clock input-source priority interface interface network-clock input-source 10 interface GigabitEthernet 0/0/1 Elect 10MHz and BITS as Input Sources network-clock input-source priority external {R0 |R1 } input source ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 133 SYNC-E to distribute it to other routers. Figure 29. SYNC-E Clock Source ASR903-R1 ASR903-R3 Loopback10: 10.10.1.1 Loopback10: 10.10.3.3 Gi0/1/1 Gi0/1/0 Gi0/1/0 Gi0/1/1 Gi0/1/0 Gi0/1/1 Gi0/1/2 Gi0/1/0 Gi0/1/4 ASR903-R2 ASR903-R4 Loopback10: 10.10.2.2 Loopback10: 10.10.4.4 Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 134 ! enable sync-e under interface interface GigabitEthernet0/1/1 description to R4 synchronous mode network-clock synchronization automatic ! enable clock selection algorithm network-clock synchronization ssm option 1 ! to select E1 or T1 type ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 135: Verifying Clocking

    SSM Option : 1 T0 : External R1 e1 crc4 120ohms ! clock is synced to Hold-off (global) : 300 ms Wait-to-restore (global) : 30 sec Tsm Delay : 180 ms Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 136 SSM Tx: ENABLED SSM Rx: ENABLED Priority: 10 QL Receive: QL-PRC QL Receive Configured: - QL Receive Overrided: - QL Transmit: - QL Transmit Configured: - Hold-off: 300 Wait-to-restore: 20 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 137 Equipment Clock : 2048 (EEC-Option1) Clock Mode : QL-Enable ESMC : Enabled SSM Option : 1 T0 : GigabitEthernet0/1/1 Hold-off (global) : 300 ms Wait-to-restore (global) : 30 sec Tsm Delay : 180 ms Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 138: Ptp Configuration

    Here is the topology to use for PTP configuration. ASR903-R1 and R2 will be configured as BC, ASR903-R3 as TC, and ASR903-R4 as slave to synchronize with R1 and R2. ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 139 ! upstream master and itself slave transport ipv4 unicast interface Lo10 negotiation clock source 192.168.2.11 ! upstream master IP address clock-port Master master ! master for the downstream slaves transport ipv4 unicast interface Lo11 negotiation Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

  • Page 140: Verifying Ptp And Clock Synchronization

    Verifying PTP and Clock Synchronization ASR903-R1# show ptp clock running domain 0 PTP Boundary Clock [Domain 0] State Ports Pkts sent Pkts rcvd Redundancy Mode PHASE_ALIGNED 424467 362306 Hot standby PORT SUMMARY PTP Master ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...
  • Page 141 Wait-to-restore (global) : 30 sec Tsm Delay : 180 ms Revertive : No Nominated Interfaces Interface SigType Mode/QL Prio QL_IN ESMC Tx ESMC Rx Internal NA/Dis QL-SEC *PTP (Dom 0) NA/En QL-PRC Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...
  • Page 142 Port Addr SLAVE unicast slave Lo10 Slave 10.10.158.1 SESSION INFORMATION SLAVE [Lo10] [Sessions 2] Peer addr Pkts in Pkts out In Errs Out Errs 10.10.158.1 160990 53148 10.10.158.2 160989 53147 ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 143: Chapter 12 Cisco Asr 903 Software Upgrade

    Cisco ASR 903 Software Upgrade Software Boot up options ▀ Chapter 12 Cisco ASR 903 Software Upgrade Software Boot up options Software packages in ASR 903 are broadly categorized into two parts as below • Consolidated package mode • Sub package mode...

  • Page 144: Sub Package Mode

    Step 3 Configure the NVRAM boot system command to boot the packages.conf file. Router# configure terminal Router(config)# boot system bootflash:issu/packages.conf Router(config)# end Router# write mem Step 4 Reload the router. ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 145: Issu One Shot Upgrade Overview

    ISSU One Shot Upgrade Overview The ISSU one shot update is the preferred method of updating software on a dual RSP ASR 903 system. The one shot update is designed to operate optimally when the router is booted in sub-package mode. In this mode, the router will perform rolling upgrades of interface module software (and firmware if applicable).

  • Page 146: Issu Preparation

    Directory of stby-bootflash:/issu/ 6380 Apr 18 2013 22:38:05 +00:00 packages.conf 223480164 Mar 14 2000 08:17:36 +00:00 asr903rsp1-universal.03.08.01.S.153-1.S1.bin 34371940 Apr 18 2013 16:01:00 +00:00 asr903rsp1-espbase.03.08.01.S.153-1.S1.pkg 5646 Apr 18 2013 16:01:00 +00:00 asr903rsp1-packages- ▄ Cisco ASR 903 Router Design and Deployment Guide OL-30526-01...

  • Page 147: Issu Procedure

    Wait for the original active RP to reboot. This will occur after the completion of STAGE 5. Step 4 Connect to the new active console wait for the redundancy state to return to SSO state. Appendix A References ASR 903 Web site: http://www.cisco.com/en/US/products/ps11610/index.html Cisco ASR 903 Router Design and Deployment Guide▄ OL-30526-01...

Table of Contents